Adhesive Tapes

Adhesive and barrier tapes are rolled tapes used on site to mark hazards, cordon off work areas and protect metal surfaces from corrosion. The current range covers 75mm x 500m yellow and black barrier tape in adhesive and non-adhesive versions, and Olympic Fixings anti-corrosion tape in 50mm x 10m rolls.

For electrical insulation, PVC insulation tape is stocked separately. Order on a trade account for trade pricing, and in-stock rolls ordered before the 5pm weekday cut-off arrive the next working day across NI and ROI.

BTY In-Stock

75mmx500m Yellow & Black Barrier Tape Roll (Non Adhesive)

£10.24 inc. VAT

HTY In-Stock

75mmx500m Yellow & Black Barrier Tape Roll Adhesive

£8.29 inc. VAT

093-353-010 In-Stock

Olympic Fixings Anti-Corrosion Tape 50mm x 10m

£9.59 inc. VAT

Choosing barrier and protective tapes for site work

Site tapes are easy to overlook until a job needs a cordon, a floor marking or a quick protective wrap. Knowing which tape does which job saves a wasted trip.

Non-adhesive barrier tape

Non-adhesive yellow and black barrier tape is tied between posts, stands or fixed points to cordon off an area such as an open floor void, a work zone under an overhead installation or a trench. It is a visual warning rather than a physical barrier, so it should be used alongside other controls where there is a risk of falls or contact with live equipment.

Adhesive hazard tape

The adhesive version sticks directly to floors, steps, machinery, doorframes and edges to highlight trip hazards, low headroom or restricted areas. Clean and dry the surface first for best adhesion.

Anti-corrosion tape

Anti-corrosion tape is wrapped around buried or exposed metal such as pipework, bolts, fixings and threaded rod to keep moisture and air away from the surface. Typical uses include:

Wrapping steel fixings or clamps at ground level or in damp locations
Protecting threaded rod and bracket joints outdoors
Sealing around metal where dissimilar materials meet

Overlap each turn as recommended by the manufacturer and work from the bottom up so water runs off rather than into the wrap.

Related products

For insulating conductors and colour coding, use PVC insulation tape. For a weatherproof finish on joints and terminations, consider heat shrink, and for sealing around penetrations see adhesives and sealants.

Meteor Electrical is family-run and has supplied the trade for over 40 years from Cookstown, Cashel and Saggart. Free delivery applies over £30 or €35 ex VAT.

FAQ's Ask Your Own Question

What is the difference between adhesive and non-adhesive barrier tape?: Non-adhesive barrier tape is designed to be tied between posts or fixed points to create a temporary cordon, while adhesive barrier tape sticks to surfaces such as floors, steps and machinery to mark hazards permanently or semi-permanently. Both use yellow and black stripes for visibility. Choose based on whether you need a cordon or a marked surface.
Is barrier tape enough to protect a work area?: Barrier tape gives a clear visual warning but does not physically stop people entering an area, so it may not be sufficient on its own where there is a serious risk such as a fall, open excavation or exposed live parts. Your risk assessment should decide whether physical barriers, signage or supervision are also needed. Follow site rules and current health and safety guidance.
What is anti-corrosion tape used for?: Anti-corrosion tape is wrapped around metal pipes, fixings, threaded rod and joints to seal out moisture and oxygen, slowing rust and corrosion. It is often used on buried or outdoor steelwork and where metal passes through damp ground or masonry. Apply it to a clean surface with overlapping turns, following the manufacturer's application guidance.
Can I use barrier tape as insulation tape?: No. Barrier and hazard tapes are not designed or rated for electrical insulation. For insulating, identifying or bundling conductors, use PVC insulation tape that is made for electrical use. For permanent insulation or weatherproofing on joints, heat shrink sleeving or a proper jointing kit is usually the more reliable choice.
How do I make adhesive hazard tape stick to a floor?: Clean the floor to remove dust, grease and moisture, let it dry fully, then apply the tape and press it down firmly along its length, ideally with a roller. Avoid applying in very cold or damp conditions, as adhesion drops. On heavily trafficked floors, rounded corners and a sealed edge help stop the tape lifting.
How long is a roll of barrier tape?: The barrier tape in this range comes in 75mm wide rolls that are 500m long, available in both adhesive and non-adhesive versions. That length suits large sites and repeated use. The Olympic Fixings anti-corrosion tape is supplied in 50mm x 10m rolls, suitable for wrapping fixings and short pipe runs.